Can You Have a Window in a Shower in Florida? Safety Glass, Glass Block, the Sill and Ventilation
Yes — the Florida Building Code allows a window in a shower; it sets rules for the glass, not a ban. Glazing in a wall containing or facing a shower is a hazardous location when its bottom exposed edge is less than 60 inches above the standing surface, so that glass must be safety glazing that passes the code’s impact test and carries a label that stays visible [1]. Glass block built to the code’s glass unit masonry section is exempt from that test [1][2]. A bathroom window of at least 3 square feet, half of it openable, also counts as the room’s ventilation; without one, the code asks for an exhaust fan to the outdoors [1][3].

Is a window in a shower allowed in Florida?
Yes. The 2023 Florida Building Code, Residential does not forbid a window in a shower; it treats glass in or beside a shower as a hazardous location for glazing and sets what that glass has to be [1].
The rule is §R308.4.5, glazing and wet surfaces. It covers glazing in walls, enclosures or fences containing, facing or adjacent to bathtubs, showers, hot tubs, spas, saunas, steam rooms and swimming pools, where the bottom exposed edge of the glazing is less than 60 inches measured vertically above any standing or walking surface [1]. It applies to single glazing and to each pane of a multi-pane window [1].
The photograph at the top of this page shows a window of this kind on one of our jobs in Sarasota: a glass-block window in the block wall at the end of a long shower, with the grey PVC shower pan liner laid and turned up the walls below it and PEX supply lines in the opened walls.
Does a shower window have to be tempered or safety glass?
If its bottom edge is less than 60 inches above the shower floor, yes — it must be safety glazing [1]. The code measures from the standing surface, which in a shower is the floor you stand on [1].
Glazing in a hazardous location has to pass the impact test of CPSC 16 CFR 1201, Category II unless the code’s table says otherwise; glazing in shower and bathtub enclosures may instead be tested to ANSI Z97.1 [1]. Each pane must carry a manufacturer’s designation naming who applied it, the type of glass and the safety-glazing standard it meets, and that mark must be visible in the final installation [1]. Trade practice is to meet the rule with tempered or laminated glass; the code’s test, not the word on the invoice, is what decides.
There are two exceptions. Glazing more than 60 inches away, measured horizontally from the edge of the shower, is not covered; nor are outboard sacrificial panes in laminated insulating glass units where the outside of the unit is not exposed to a hazardous location [1]. A window whose bottom edge is 60 inches or more above the shower floor is outside this rule [1].
We did not find an exception in §R308.4.5 for an existing window when the shower around it is rebuilt. Our reading: whether an old window in a remodelled shower has to be changed is the building official’s call, and the time to ask is before the walls are closed.
Is glass block allowed in a shower?
Yes. The safety-glazing impact test of §R308.3 lists glass unit masonry complying with Section R607 as an exception, so a glass-block panel built to that section does not have to pass it [1][2].
In the 2023 Florida Building Code, Residential, glass unit masonry is Section R607, not R610 [2]. It covers glass-block panels in load-bearing and non-load-bearing exterior and interior walls [2]. It requires hollow units with a minimum average glass face of 3/16 inch, sets maximum panel areas — 144 square feet for an exterior panel of standard units at the base wind pressure, 250 square feet for an interior one — and asks that the sill be coated with a water-base asphaltic emulsion before the units are bedded [2]. Expansion joints stay free of mortar and are filled with resilient material, and the units are laid in Type S or N mortar [2].
One glass-block maker’s instructions add a step for wet rooms: Pittsburgh Corning’s mortar installation guide says that if the panel will function as a shower wall, after about a week the mortar joints on both sides should be coated with tile grout sealer for mold and mildew protection, and that sealant goes around the perimeter of the panel on both sides [5]. That is one maker’s instructions, not necessarily the brand in a given house.
How do you keep a shower window sill from rotting?
Slope it so water runs back into the shower. Schluter’s shower system installation handbook says that all horizontal surfaces — it names benches, curbs, window sills and shelves — must be sloped toward the shower drain [4]. A sill that is flat, or tips toward the glass, holds water against the window frame.
The same handbook says its waterproofing membrane goes up to the height of the showerhead at minimum, and that treating every penetration through the membrane is the specifier’s responsibility [4]. It does not show a window detail. Our reading: a window opening below showerhead height is a hole in the waterproofed wall, so the membrane has to continue over the sill and the sides of the opening and be sealed where it meets the frame. How to make that joint is a question for the maker of the membrane you use and the maker of the window.
The sill is also where a window in a shower usually meets the shower pan. What has to sit under the floor and how far the liner turns up the walls is covered in what is under your shower floor; the signs that water is getting past it are in signs of a leaking shower pan.
Does a shower window count as bathroom ventilation?
It can. The Florida Building Code, Residential says bathrooms must have windows with at least 3 square feet of glazing, one-half of which must be openable [1].
The window is one of two ways to meet it. The glazing is not required where artificial light and a local exhaust system are provided, with the exhaust rate set by Section M1507 and the air exhausted directly to the outdoors [1]. Section M1507 sets that rate for bathrooms and toilet rooms at 50 cfm intermittent or 20 cfm continuous, and says bathroom exhaust air may not be recirculated or dumped into an attic or crawl space [3].
Our reading: a glass-block panel with no opening section does not give the openable half, so a bathroom that relies on it for light still needs the fan.
How do you get privacy with a window in the shower?
With glass you cannot see through, or by putting the glass high. Trade practice is patterned or obscured glass, or glass block, which lets light in and blurs the view.
A window set high enough that its bottom edge is 60 inches or more above the shower floor is out of the safety-glazing rule as well as out of sight lines [1]; below that line, whatever glass gives the privacy still has to be safety glazing [1].
Who builds a shower around a window?
We are plumbers: we build the shower pan and the plumbing around a window that is already there, and leave the window in place.
The photograph below is from Belleair Beach: a grey PVC liner laid in a corner shower against a concrete-block wall, with the shower valve rough-in at the upper left and a window opening at the lower left, beside the shower framing. How big the shower itself has to be is covered in the minimum shower size in Florida.

What this means in Clearwater and across Tampa Bay
The Florida Building Code is the state’s code, so the 60-inch safety-glazing line, the glass-block exception and the bathroom ventilation rule are the same in Clearwater, St. Petersburg and Tampa [1][2][3]. The sections on this page are from the 8th edition (2023).
The two photographs on this page are ours, from Sarasota and Belleair Beach: shower pan liners laid next to a window that stayed where it was. If you are rebuilding a shower that has a window in it, call 727-470-7126 and we will talk through the pan and the plumbing.
We build shower pans and the plumbing around them in Clearwater, Tampa and across Tampa Bay. Kate, our AI voice assistant, answers the phone 24/7 and takes the request; site work is scheduled Monday to Friday, 8am to 6pm.
Call 727-470-7126FAQ
Can you have a window in a shower?
Yes. The Florida Building Code, Residential allows it and treats glass in or beside a shower as a hazardous location: if the bottom edge is less than 60 inches above the shower floor, the glass must be safety glazing [1].
Does a window in a shower need to be tempered?
It must be safety glazing if its bottom edge is less than 60 inches above the standing surface: glass that passes the CPSC 16 CFR 1201 impact test (or ANSI Z97.1 for shower enclosures) with a visible label [1]. Tempered or laminated glass is how the trade usually meets it.
How high does a window have to be in a shower to not need safety glass?
Its bottom exposed edge must be at least 60 inches above the shower floor, or the glass must be more than 60 inches away horizontally from the edge of the shower [1].
Is glass block OK in a shower?
Yes. Glass unit masonry built to §R607 is an exception to the safety-glazing impact test [1][2]. One maker, Pittsburgh Corning, says to coat the mortar joints of a shower-wall panel with tile grout sealer after about a week [5].
How do you waterproof a window in a shower?
Schluter’s handbook says window sills must slope toward the shower drain and its membrane goes at least to showerhead height [4]. Carrying the membrane over the sill to the frame and sealing it there is our reading; follow the membrane maker’s detail.
Is a window in the shower a bad idea?
Not if the glass meets the safety rule and the sill sheds water into the shower [1][4]. The sill is the part to watch: a flat one holds water against the frame.
Does a bathroom need a window or an exhaust fan in Florida?
One or the other. The code asks for at least 3 sq ft of window glazing, half of it openable, or artificial light plus an exhaust fan to the outdoors at 50 cfm intermittent or 20 cfm continuous [1][3].
Can a shower be rebuilt around an existing window?
Yes. That is the work we do as plumbers: we build the shower pan and the plumbing around a window that is already there, as in the Sarasota and Belleair Beach photographs on this page.
Sources
We review and cite. We do not reproduce a paper or a manual — follow the links for the originals.
- [1]2023 Florida Building Code, Residential, 8th Edition — Chapter 3, Building Planning (§R303.3 Bathrooms, §R308.1, §R308.3, §R308.3.1, §R308.4, §R308.4.5) — Florida Building Commission / International Code Council (read on UpCodes) · 2023Law / code · §R308.4.5: glazing in walls, enclosures or fences containing, facing or adjacent to hot tubs, spas, whirlpools, saunas, steam rooms, bathtubs, showers and pools where the bottom exposed edge is less than 60 in measured vertically above any standing or walking surface is a hazardous location; applies to single glazing and each pane in multiple glazing; exception 1: glazing more than 60 in measured horizontally from the water’s edge of a tub/pool or the edge of a shower, sauna or steam room; exception 2: outboard sacrificial panes in laminated insulating glass units where the exterior is not exposed to a hazardous location; §R308.1: each pane in a hazardous location carries a manufacturer’s designation (who applied it, type of glass, safety glazing standard) visible in the final installation; §R308.3: glazing in hazardous locations passes §R308.3.1; exception 3: glass unit masonry complying with Section R607; §R308.3.1: CPSC 16 CFR 1201, Category II unless Table R308.3.1(1) says otherwise; exception: glazing in hot tub, sauna, bathtub and shower enclosures may be tested to ANSI Z97.1; §R303.3: bathrooms provided with aggregate glazing area in windows of not less than 3 sq ft, one-half openable; exception: not required where artificial light and a local exhaust system are provided, rates per M1507, exhausted directly to the outdoors; read 2026-11-16
- [2]2023 Florida Building Code, Residential, 8th Edition — Chapter 6, Wall Construction (§R607 Glass Unit Masonry) — Florida Building Commission / International Code Council (read on UpCodes) · 2023Law / code · §R607.1: panels of glass unit masonry in load-bearing and nonload-bearing exterior and interior walls; §R607.2: hollow units partially evacuated, minimum average glass face thickness 3/16 in, reclaimed units prohibited; §R607.4.1: exterior standard-unit panel max 144 sq ft at 20 psf; §R607.4.3: interior standard-unit panel max 250 sq ft; §R607.6: before bedding, sill area covered with a water base asphaltic emulsion coating; §R607.7: expansion joints free of mortar, filled with resilient material; §R607.8: Type S or N mortar; R610 in this edition is structural insulated panel wall construction, not glass block; R607 does not mention showers or wet areas; read 2026-11-16
- [3]2023 Florida Building Code, Residential, 8th Edition — Chapter 15, Exhaust Systems (§M1501.1, §M1507.2, Table M1507.4) — Florida Building Commission / International Code Council (read on UpCodes) · 2023Law / code · Table M1507.4: bathrooms-toilet rooms, mechanical exhaust capacity of 50 cfm intermittent or 20 cfm continuous, rated at 0.25 in wc minimum static pressure; §M1507.2: exhaust air from bathrooms and toilet rooms not recirculated, exhausted directly to the outdoors, not into an attic, crawl space or other areas inside the building; §M1501.1: exhaust discharged to the outdoors; read 2026-11-16
- [4]Schluter-Shower System Installation Handbook (04/2023) — Schluter-Systems · 2023Manufacturer's manual · copy hosted by a retailer; edition 04/2023 on the cover; p. 7 and repeated in later system sections: all horizontal surfaces (e.g. benches, curbs, window sills, shelves) must be sloped toward the shower drain; KERDI membrane installed up to the height of the showerhead at minimum; in enclosed showers on all surfaces including the ceiling, door jambs and door header; treating all penetrations through the membrane is the specifier’s responsibility; no window detail drawing found in the text; one maker’s instructions, not necessarily the system in any given shower; read 2026-11-16
- [5]Mortar Glass Block Installation System — Assembly Instructions (GB-243, Rev. 11/11) — Pittsburgh Corning Corporation · 2011Manufacturer's manual · copy hosted by a retailer; materials list includes expansion strips, panel anchors, glass block sealant and asphalt emulsion depending on application; apply sealant around the perimeter of the panel on both sides; if the glass block panel will function as a shower wall, after about a week coat the mortar joints on both sides with tile grout sealer for mold and mildew protection; one maker’s instructions, not necessarily the brand in the photographs; read 2026-11-16
Questions About Your Own System?
Send a photo of what you have. We answer with what it is and what it needs.
See our PEX-A Shower & Tub Rough-In service →
Licensed CFC1432506 · Insured · Clearwater, FL + 50 miles
